Account
We offer FREE UK Mainland delivery for orders over £50! (EX VAT exclusions apply).
We offer FREE UK Mainland delivery for orders over £50! (EX VAT exclusions apply).
Found 370 product(s). Showing product(s) 1 to 370.
Galvanised mild steel Thickness 1.0mm Packed 100 per box Weight per 100: 5.75Kg ... read on
Galvanised mild steel Thickness: 0.9mm Packed 100 per box Weight per 100: 3.47Kg Technical Details Material EN 10142 Galvanised Mild Steel Thickness 0.9mm Availa... read on
The BTALU concealed hanger is one solution to connecting timber members together without seeing the connector. It is designed to be fixed to the header timber and then fully... read on
The ETB concealed connector comes in two parts. The first is pocketed in the header timber and fixed with nails, while the second part is fitted to the end of the beam with screw... read on
Glide shoes are specially designed to allow horizontal movement between raised tie trusses and wallplates.The GS allows lateral movement of raised tie trusses up to 15mm during i... read on
The TU galvanised steel, load rated hanger provides an aesthetically attractive connection for exposed beams. Mild steel dowels and screws are included. TUBSL or TUBSR, factory... read on
The TCP truss clip attaches girders, trusses and rafters to wall plates to provide wind restraint. TCP Truss Clips may be used for general purposes, strongback attachment... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
These products act to secure two leaves of a cavity wall to each other, allowing them to act as one structurally. A cavity tie usually incorporates some mechanism, (usually a cha... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
The PBH is suitable for heavy duty post support applications including Glulam timber posts,with a standoff height of 216mm. Dowels included. PBH75 suitable for posts 75 x 75mm to... read on
Galvanised spring steel wire 2.6mm diameter Packed 200 per box Weight per 100: 1Kg ... read on
Channel to timber connector - maximum drop 120mm. Material: Galvanised Mild steel to BS EN 10142:2000 Packed: 100 per box Weight per 100: 3.10kg ... read on
A 4.5mm Newbuild wall tie for securing external masonry to timber frames. The first helical wall tie was tested to EN846 for timber frame construction. Used for domestic and smal... read on
Fixes to stud, using adhesive strip, and used to secure 12mm plywood. The plywood allows services to be fixed to the face of a partition. Material Galvanised Mild Steel ... read on
Designed For: Use with timber joist ceilings, floors and ceiling systems for increased acoustic performance Colour: Silver Grey Coating: Electroplated Zinc Tough hangers used ... read on
With these site adjustable hangers, you can always have the right hanger available for those special rush projects. This versatile range of products attaches joists/rafters to ti... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Glide shoes are specially designed to allow horizontal movement between raised tie trusses and wallplates.The GS allows lateral movement of raised tie trusses up to 15mm during i... read on
SIZES 200mm 225mm 250mm 275mm BBA Approved light duty housing ties (Agrément Certificate: 17/5462). Application - A light duty wall tie u... read on
Resin to Resin Remedial Wall Ties (HELI-4.5-ONE, HELI-6-ONE) Used when the existing ties have either corroded or insufficient ties have been used. Tying both the inner (load bea... read on
When fixing a stainless steel tie to a mild steel frame, an isolation pad should be used to separate the dissimilar metals and prevent a bimetallic reaction.... read on
SST Starter Tie supplied complete with nylon plug. Used where new walls are being built directly from existing brickwork. Alternatively can be used without plug and screwed direc... read on
Supplied complete with 50mm x 3.35mm Stainless Steel Annular Ring Nails. Application - This type of timber frame wall tie is right for domestic and small commerci... read on
Glide shoes are specially designed to allow horizontal movement between raised tie trusses and wallplates.The GS allows lateral movement of raised tie trusses up to 15mm during i... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Fixing lighting or suspended wire to steel profiles, cable to steel purlins or suspended ceilings to steel profiles Use with timber joist ceilings, floors and ceiling systems ... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
Fixes to stud, using adhesive strip, and used to secure 18mm plywood. The plywood allows services to be fixed to the face of a partition. Material Galvanised Mild Steel ... read on
The ABW is an adjustable post base with a stand off for the post to help prevent moisture induced decay to the timber post. Designed for versatility and cost effectiveness. ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
BBA Approved general purpose wall ties (Agrément Certificate: 17/5462). Application - A general-purpose wall tie for applications such as small commercial bui... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
These products both allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These sy... read on
DESIGNED FOR: Ceiling Bracket SIZE: 25mm x 25mm BOX QUANTITY: 100... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Glide shoes are specially designed to allow horizontal movement between raised tie trusses and wallplates.The GS allows lateral movement of raised tie trusses up to 15mm during i... read on
The APB features a post mounting plate on a screw allowing it to be adjusted to a specific standoff height ranging from 100-150mm. Suitable for post sizes 100 x 100mm to 200 x 20... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Designed For: Use with timber joist ceilings, floors and ceiling systems for increased acoustic performance. Colour: Silver Grey Coating: Electroplated Zinc Tough hangers used... read on
Designed to attach timber members at irregular angles, these connectors can be bent on site from 0° to 135°. The staggered nail pattern reduces the possibility for s... read on
The H and L straps are designed to The Building Regulations for horizontal and vertical restraint. Heavy restraint straps meet requirements for lateral restraint of roof ... read on
The VST1 tie range has a Multidrip feature to prevent moisture from traveling across the cavity. Its categorisation as a Type 1 wall tie means the VST1 tie is suitable for most b... read on
Isover Acoustic Partition Roll. Insulating your home will become an easy task by employing this ISOVER APR 1200 50MM insulation roll. This acoustic partition roll is a non-combu... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
These products both allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These sy... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Encasement Clip (Steel Framing Clip) for cladding structural steel sections. Material: Spring Steel Surface Finish: Black Phosphate to EN 12476 Packed: 100 per box Weight p... read on
Spring steel 0.45mm thick Standard Finiush B & K Packed 500 per box Weight per 500: 2.2Kg ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
FB20 galvanised fixing band is for all general light strapping needs. Perfect for DIY, industrial and agricultural applications. Comes in convenient 10 metre rolls. FB20, w... read on
The RHMSK is designed to support solid timber joists, I-joists or metal web joists from masonry walls. Material Pre-galvanised mild steel Benefits Due to non-welded man... read on
Galvanised mild steel Thickness 1.0mm Packed 100 per box Weight per 100: 7.5Kg Please note: images are for illustration only.... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Hold Down Clip for 40mm Boards Material Hold Down Clip for 40mm Boards Surface Finish Dry Oil Packed 500 per Box Weight per 100 0.63kg Please note picture is... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Soffit fixed both sides where fixings can be made directly above. Heavy Duty. Hole size standard 12mm to suit M10 expansion bolts or M10 head bolt. Design load resistant dependan... read on
Used to stabilise solid or rubble walls, repair delaminated brickwork and to reconnect separated internal party walls to the external leafs. Installation: 1. Drill hole to requ... read on
For suspending from 1.5mm to 4mm flange Material Spring Steel Surface Finish Zinc & Yellow Passivate to EN 12329 Packed 100 per box Weight per 100 0.87... read on
Glide shoes are specially designed to allow horizontal movement between raised tie trusses and wallplates.The GS allows lateral movement of raised tie trusses up to 15mm during i... read on
The timber panel closer helps minimise air leakage at the joint between closed panels and also prevents damage to the exterior substrate when using a screw alone. Material ... read on
The JES is a two piece metal-work system which enables the use of engineered timber I-joists in loft conversions, offering a safe and economic alternative to the tradit... read on
The SDE is a two piece, width adjustable face fix hanger. The two separate components that make up the SDE system can be adjusted to suit a range of joist widths betwee... read on
E5/2C50 Reinforced angle brackets are suitable for structural applications in framing and wood-frame houses. Material Galvanized steel S250GD + Z275 according to NF EN 10346... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Provide added strength and stability. Galvanised or stainless steel finish. Assists resistance to tensile stresses where settlement occurs. Easily incorporated into mortar&nb... read on
The CPT post base provides a clean look while providing a 25mm stand off height above the ground. reducing the potential for decay at the post end. The CPT can be fixed to a con... read on
Gripple B-Lock Wire Rope Suspension Kits are ideal to hang signs, HVAC, catenary, electrical cables etc, designed with an innovative fast-locking side release mechanism.FEATURES ... read on
These products allow new walls to be joined to existing structures. They can be used to extend an existing structure, or they can be used to help create an additional leaf where ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
SAE and SAI ranges are heavy-duty hangers designed for applications requiring additional strength. SAE hangers are nailed using square twist nails but have bolt holes for 1... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Superior alternative to unreliable, slow and costly timber struts. Meets bracing requirements for long span domestic floors. Material Pre-galvanised mild steel. Featu... read on
The PISBMAXI is a heavy duty elevated post base to suit various sizes of timber and Glulam posts. Material Material Grade S235 Finish Post hot dip galvanised. Benefits T... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
The Simpson Strong-Tie RCKW is a heavy duty rigid connector that has been developed to resist an overturning moment at the base of exterior kneewalls and parapets as we... read on
Used to suspend a variety of HVAC, mechanical and electrical services from different substrates, to be used with B-Lock side release hangers. Ideal for the fast suspension of ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
Isover Acoustic Partition Roll. Insulating your home will become an easy task by employing this ISOVER APR 1200 25MM insulation roll. This acoustic partition roll is a non-combu... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
A range of heavy duty (welded) and light duty (bent and/or twisted) stems. Available in standard stem lengths, head sizes and hole configurations with other options available on ... read on
The ITBS solves the problem of skew hangers in I-joist to I-joist connections. It can be handed left or right on site by the carpenter, removing confusion when the floor is built... read on
This range of ties allow masonry walls to be tied back to other structures (steelwork or masonry) providing restraint in one direction but allowing movement in the other. This is... read on
ETFSS hold down strap provides restraint against uplift to timber frame structures keeping them firmly to the ground. Quick and simple to install One size strap suits cavitie... read on
The SPR connector supports rafters from other timber members and can be sloped up or down by up to 45 degress. Slope angle can be adjusted on-site. Adjustable between 0 and 4... read on
Light angle brackets are used in a large number of DIY applications and are commonly used for reinforcing furniture assemblies. FEATURES Material Steel S235JR ... read on
Developed for the quick fastening of cable basket to Gripple Pipe Support Brackets, Fast Trak and G-Brackets. Secure – prevents uplift and slide of cable basket Versati... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
EFIXR angle brackets are intended for all assemblies for the design and installation of interior and exterior joinery. EFIXR stiffener improves rigidity particularly for large mo... read on
Isover Acoustic Partition Roll. Insulating your home will become an easy task by employing this ISOVER APR 1200 100MM insulation roll. This acoustic partition roll is a non-comb... read on
Used to suspend a variety of HVAC, mechanical and electrical services from different substrates, to be used with B-Lock side release hangers. Ideal for the fast suspension of ... read on
A heavy-duty wall tie suitable for most buildings in the UK of any height, with cavities up to 150mm. Used for collar jointed walls, in full fill cavities or where the prevention... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
The HGUQ joist hanger is designed to support trusses and girder trusses from timber members. The HGUQ uses SDS screws instead of nails for even faster and easier installatio... read on
The THM (Truss Hanger Mono) is a joist hanger for supporting mono trusses from timber members. The THM hanger offers two installation options: Square twist nail... read on
The THA is a one-piece joist hanger supporting trussed rafters and composite timbers from timber members. The THA can be installed with a number of fixing options, for greater lo... read on
Galvanised mild steel Thickness 1.5mm Packed 1000 per box Weight per 1000: 15Kg ... read on
For suspending various items from Purlin Material Mild Steel to EN10139 Surface Finish Zinc Plate to EN 12329 Packed 100 per box Weight per 100 1.5kg ... read on
Pre-fabricated bracket solution offering speed, flexibility and efficient use of space, for the installation of electrical containment, pipework, ductwork and other mechanical se... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Pre-fabricated bracket solution offering speed, flexibility and efficient use of space, for the installation of electrical containment, pipework, ductwork and other mechanical se... read on
The AKR bracket is reinforced around the bend, which significantly increases the rigidity and strength of the bracket. One-piece connector. Reinforced corners provide enhance... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
The JHM and JHMI range of joist hangers can be used to connect solid sawn joists, trusses and engineered joists to masonry walls or steel beams. Material Pre-galvanised mild ... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
28/15 slotted and holed channel for surface fixing. Slots and holes repeat every 75mm to ensure a fixing point is available along the entire length. Various fixings can be used i... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Screw in wall starter with nylon wall plug, WST provides lateral stability to brickwork or blockwork walls. Can be installed horizontally or at a 30° angle to the mortar join... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Galvanised Mild Steel Thickness 0.5mm Packed 100 per box Weight per 200: 12Kg ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
For fixing stud to masonry - maximum stand off 175mm. Material Galvanised Mild steel to BS EN 10142:2000 Packed 100 per box Weight per 100 7.30kg ... read on
An accepted method of tying masonry to a framed structure is the use of steel channels and ties. This allows the channel to be fixed to the framed structure during or shortly aft... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
The ABR angle brackets with rib can be used in high loaded timber structures. These brackets are made of stainless steel and are recommended in aggressive atmospheres ... read on
The A35E anchor’s exclusive bending slot allows instant, accurate bending on site for all two and three-way connections. • Balanced, completely reversible design ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
Light reinforced angle brackets are used to assemble small structural joinery for internal and external applications. Material Pre-galvanised mild steel. Benefits Multi... read on
The SFLH is an innovative single piece hanger designed to support timber joists from masonry walls, without the need for masonry above the course of blockwork supporting the... read on
- Systems that suit all primary structure types.- Provides secondary support for all types of external finishes.- Provides weather tight envelope early in the build programme.- E... read on
Reinforced angle brackets are suitable for structural applications in framing and timber framed houses as well as light gauge steel construction. Material Galvanized steel S2... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Nail plates are used to connect two or more timber members together. They are available in a variety of sizes. Material Pre-glavanised mild steel. Grade S250GD Benefits ... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Anti Vibration Ceiling Hanger Material Mild Steel to DIN EN 10111/10051 Surface Finish Zinc Plate to DIN 50961 Packed 100 per box Weight per 100 4.50kg &... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
Designed to provide ties for trusses and rafters likely to be subject to high winds, this versatile range may be used for general purposes, strongback attachements and as all-pur... read on
A direct replacement for traditional restraint straps, the innovative design of these lightweight straps allows ease of handling and installation whilst maintaining the ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
A 75mm wide, fine stainless steel mesh on a 30m roll. Easy to cut and install. Allows roof space ventilation and helps prevent birds and insects from gaining access via soffits. ... read on
SST Starter Tie supplied complete with nylon plug. Used where there is a cavity and a new wall needs to be built. Supplied with drip. SST-225-STST Compressive... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Simpson Strong-Tie SAE heavy duty face fix hanger, designed for applications requiring additional strength. Hangers have bolt holes for 12mm fasteners into the face and whilst pr... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
The HGUS joist hanger is designed to support trusses and girder trusses from timber members. Material Pre-galvanised mild steel For sizing and technic... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
The MH is a one piece galvanised hanger available in a range of widths for light duty applications such as trimmers and ceiling joists of rectangular section. THe MH can also be ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
The UK’s most popular solution to the tying-in of new walls to existing masonry walls/columns. The only system with “snap out” ties which can be positioned anyw... read on
The PWT200 is the first connector specifically designed and engineered to connect the party walls of timber framed buildings. It’s manufactured using minimum material secti... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
The IUSE is a face fix hanger for supporting I-joists from timber members.This hanger incorporates the “Strong Grip™” which secures the I-joist withoutthe need ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
The SPF can be used to connect two timbers that cross over at 90 degrees to each other and can be used with a number of timber dimensions. The SPF are handed, left and right, and... read on
Glide shoes are specially designed to allow horizontal movement between raised tie trusses and wallplates.The GS allows lateral movement of raised tie trusses up to 15mm during i... read on
A range of heavy duty (welded) and light duty (bent and/or twisted) stems. Available in standard stem lengths, head sizes and hole configurations with other options available on ... read on
SSFT Starter Frame Tie. Used for fixing timber door and window frames to brickwork by building into mortar courses as construction progresses Compressive Load Capacity: ... read on
For Suspension by Wire Rope, Single Strand Wire and Strap Material Mild Steel Surface Finish Zinc & Yellow Passivate to EN 12329 Packed 100 per box Weight per 100 0.... read on
These products both allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These sy... read on
The ITB hanger eliminates the requirement for backer blocks when supported from anI-Joist header. The bottom flange location tabs, and an open top flange, provide enhanced c... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Light angle brackets are used in a large number of DIY applications and are commonly used for reinforcing furniture assemblies. FEATURES Material Steel S235JR ... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
The SWT wall ties are used to restrain external brickwork back to timber frame building structures. The BSWT offers an outstanding combination of performance and cost in a wall t... read on
The PPA is for post base installations requiring a higher standoff distance. Material Steel S235JR according to NF EN 10025 Hotdip galvanized according to NF EN ISO 1461 ... read on
Suitable for use with cavity wall ties, the insulation retaining clip is a 75mm diameter plastic disk used to hold insulation material back to the structure,... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
These products allow the introduction of a cavity tie into a sitation where no ties are present. These stainless steel ‘wavy’ tail ties are used for remedial applicat... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
This range of ties allows masonry walls to be tied back to other structures, (steelwork or masonry) providing restraint in one direction but allowing movement in the other. This ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
The HRC is a one-piece connector for supporting hip members from the ridge beam or rafters. It is site adjustable for slopes up to 45°, to cater for the hip pitch for bo... read on
The PBS post base is designed to be installed into wet concrete and features a stand off to help prevent moisture induced decay to the timber post. Sold in Packs of 10 only. Mat... read on
This range of ties allows masonry walls to be tied back to other structures, (steelwork or masonry) providing restraint in one direction but allowing movement in the other. This ... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
The HJHM range of joist hangers can be used to connect solid sawn joists, trusses, and engineered joists to masonry walls or steel beams. Top flange provides widest area ... read on
BBA Approved general purpose wall ties (Agrément Certificate: 17/5462). Application – A general-purpose wall tie for applications such as small commerci... read on
THGQ is a heavy duty girder truss hanger designed to support multiple ply girder trusses from a vertical member of a girder truss. Use with SSH screws instead of bolts - ... read on
B-Lock wire rope hanger grips, also known as clutches, are made in Europe by Gripple and are a fast and affordable wire rope grip. They do not require and specialist tools to ins... read on
PLEASE NOTE THIS IS A MADE TO ORDER ITEM SO IS NON RETURNABLE The IUC is a face mounted concealed flange hanger for solid timber sections or engineered joists. These hangers ca... read on
The WSTC is a screw-in cavity wall tie suitable for connecting a new leaf of masonry to an existing structure. Supplied with nylon wall plug and neoprene ‘O’ ring ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
These products allow masonry walls to be restrained back to other elements of the structure. The ties, once in position, prevent sideways movement between a wall and another stru... read on
Cast in dovetail slot, available in stainless steel or pre-galvanised steel. V29s are pre-filled with polystyrene to prevent concrete ingress. Vista recommends that V29s are used... read on
The PPRC allows the structure to be adjusted after it has been built. Adjust the off the ground height from 100 to 150mm even after the post has been installed. Material dich... read on
TFLS provides the combined function of levelling and fixing the sole plate to the foundation or substructure. It comprises a universal base plate and packing pieces which ca... read on
The SMH is a range of Heavy Duty Joist Hangers designed for building into brickwork or blockwork. As standard all hangers are manufactured from 2.0mm thick pre-galvanised steel. ... read on
These products allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These systems... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Systems that suit all primary structure types. Provides secondary support for all types of external finishes. Provides weather tight envelope early in the build programme. E... read on
For Connecting 38mm Channel Material Galvanised Mild Steel to BS EN 10142:2000 Packed 250 per box Weight per 100 4.60kg ... read on
A direct replacement for traditional restraint straps, the innovative design of these lightweight straps allows ease of handling and installation whilst maintaining ... read on
Isover Acoustic Partition Roll. Insulating your home will become an easy task by employing this ISOVER APR 1200 75MM insulation roll. This acoustic partition roll is a non-combu... read on
Clip to provide 55mm stagger. Used in staggered acoustic partition system for positioning and securing studs. Material Galvanised Mild steel to BS EN 10142:2000 Packed 100 per ... read on
Isover Acoustic Partition Roll. Insulating your home will become an easy task by employing this ISOVER APR 1200 65MM insulation roll. This acoustic partition roll is a non-combu... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
JHA is a height adjustable joist hanger for supporting timber joists from timber members. Available in standard leg (JHA270) and long leg (JHA450) versions. Material Pre-gal... read on
The VTCR is designed to connect valley trusses to common trusses. Structural valley connection. Single sided for new construction or retro fit. Site adjustment for pitch. Ad... read on
Qty 100 per box Clip to provide 10mm stagger. Used in staggered acoustic partition system for positioning and securing studs. Material Galvanised Mild Steel to BS EN 10... read on
90° Bracket for Partition / Frame. Material Galvanised Mild steel to BS EN 10142:2000 Packed 100 per Bag, 1000 per box Weight per 100 1.76kg ... read on
The FMS strap provides restraint to masonry walls when the walls are supporting joist ends. They make installation easier, quicker and more cost effective - without compromising ... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
Soffit Fixed both sides where fixings can be made directly above. Heavy duty. Hole size standard 12mm to suit M10 expansion bolts or M10 head bolt. Design load resistant dependan... read on
The PBP60/50 post base is most commonly use for pergola or porch type construction, but can be used in other situations. It should be used by pair for square timber sections fro... read on
The SPA is a versatile bracket used to attach timber sole plates to concrete foundations. Material Pre-galvanised mild steel For sizing and technical information please se... read on
Stainless steel masonry-timber tie for domestic and small commercial buildings up to four storeys high. Suitable for buildings with a maximum height if 15m and cavity widths from... read on
Ceiling Suspension Bracket Material Galvanised Mild steel to BS EN 10142:2000 Packed 100 per box Weight per 100 1.90kg... read on
Drywall C Studs are lightweight C shaped galvanised mild steel sections used vertically to form a partiton wall or wall lining.Located into a floor and head track, C Studs sizes ... read on
Drip feature to prevent moisture travelling across the cavity (taking less space than vertical twist). Drip position 90mm from safety end as standard. 250mm long stainless steel ... read on
Used as a soffit fixed head restraint. Light Duty, twisted head allows for fixing a right angle for cavity. Hole size standard 12mm to suit M10 expansion bolts or M10 head bolt. ... read on
Vertical Twist feature to prevent moisture travelling across the cavity. The design means that the tie can be installed either way up. It’s categorisation as a Type 1 wall ... read on
90° Bracket for Partition / Frame. Material Aluminium Packed 100 per box, 1000 per bag Weight per 100 0.97kg ... read on
Single sided and double sided connector plates for enhanced bolt performance in timber. Conforms to BS EN 912: 1999 Annex C. Specification for toothed plate connectors. Material... read on
Vista have developed Vista Weld 3 to meet the ever increasing requirements of specifiers. Vista Weld 3 is a welded ladder type Bed Joint Reinforcement with 3mm outer wires. It is... read on
It's common practice to cut a hole in the tops of the floor joists so that pipes and electrical cables can pass through the void between an upper floor and ceiling below it - par... read on
These products act to secure two leaves of a cavity wall to each other, allowing them to act as one structurally. They incorporates a multidrip feature to discourage moisture mov... read on
Material Mild Steel to DIN EN 10111/10051 Surface Finish Zinc Plate to DIN 50961 Packed 100 per box Weight per 100 6kg - ... read on
The FMS strap provides restraint to masonry walls when the walls are supporting joist ends. They make installation easier, quicker and more cost effective - withou... read on
The BTS and SWT wall ties are used to restrain external brickwork back to timber frame building structures. The BTS and SWT offer an outstanding combination of performance a... read on
The MP is an easy to use connector for timber splices, no nails required. For non-structural applications only; not for truss applications. Material Pre-galvanised mild steel... read on
Drywall U Track is a lighweight U shaped galvanized mild steel section used at the junction of walls, ceilings and floors within a stud partition wall or lining system.U track si... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
Types 2, 3 and 4 Stainless Steel Masonry to Masonry Wall Ties.WTS2: Type 2 Wall Ties: Masonry General Purpose Type 2 wall ties are suitable for general purpose applications such ... read on
Timber to timber joist hanger to support 47mm wide joists from 100 to 150mm in depth. Manufactured from 2mm thick galvanised steel, powder coated after fabrication for superior d... read on
For use in heavy duty applications such as multiple truss units, main trimmer joists, purlin to beam connections or similar situations where unusually heavy loads occur. &... read on
A bolt down post shoe used for installing deck posts onto an existing concrete base. Size: 100x100mm ... read on
Reinforced angle bracket ABR255 has been especially developed to fix CLT panels on wood or concrete support. Very versatile, it is particularly resistant to shear loads... read on
Material Mild Steel to DIN EN 10111/10051 Surface Finish Zinc Plate to DIN 50961 Packed 100 per box Weight per 100 6kg - ... read on
The RBL Bib Lath provides plaster/render backing and is also suitable for the refurbishing of damaged or deteriorated faces of masonry walls. Available in galvanised for internal... read on
The SFLHI is an innovative single piece hanger designed to support timber joists from masonry walls without the need for masonry above the course of block work supporting the han... read on
The SP is an economical on-site method of butt jointing timbers of similar section. Suitable for use when replacing rotten floor joist ends, replacement of fire damaged timbers a... read on
The VHR head restraint is designed to restrain the top of the inner leaf of cavity walls. The standard restraint consists of 2 angles and can be used to restrain both 100mm and 1... read on
Anti Vibration Ceiling Hanger Material Mild Steel to DIN EN 10111/10051 Surface Finish Zinc Plate to DIN 50961 Packed ... read on
When fixing windows, door frames etc. to masonry, the frame tie provides enhanced mortar keying and reduces the risk of injury from sharp edges. Note: Frame tie should be fully ... read on
The SAE and SAI ranges are heavy-duty hangers designed for timber to timber applications requiring additional strength. • The hanger depth is to be at least 60% of the car... read on
A versatile range of brackets for use in 90 degree connections allowing for use of nails, screws and / or bolts and coach screws. AB Angle Brackets have a reinforced rib. Size O... read on
For suspending ceiling systems Material Galvanised Mild Steel Packed 25m coils ... read on
The Vista TPT is designed to safely tie across large cavities in traditional brick/blocks. As a result of problems experienced over wider cavities (150- 375mm) and their weight c... read on
The SFH Safety Fast Hanger is designed to support timber joists, beams and trussed rafters from masonry walls without the need for masonry above the top flange. M... read on
Long Leg Timber to Timber Hangers. Manufactured from 1.5mm thick pre-galvanised steel with 50mm wide legs, suitable for solid joist or I-Beam applications, either face fixe... read on
The RR ridge rafter connector provides alignment control and correct nailing locations. The RR may be used with any rafter slope up to 30°. For back-to-back installations, th... read on
The SMH is a range of Heavy Duty Joist Hangers designed for building into brickwork or blockwork. As standard all hangers are manufactured from 2.0mm thick pre-galvanised steel.... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
FB20 fixing band is for all general light strapping needs. Perfect for DIY, industrial and agricultural applications. Comes in convenient 10 metre rolls. FB20, which comes suppl... read on
The ‘A’ angles versatility means it can be used in many applications requiring 90° fixing. Material Pre-galvanised mild steel. For sizing and technical inf... read on
Used to suspend a variety of HVAC, mechanical and electrical services from different substrates, to be used with B-Lock side release hangers. Ideal for the fast suspension of ... read on
N3.75 square twist nails are tested and approved for use when installing Simpson Strong-Tie connectors including joist hangers, brackets and straps. CE marked to EN14592. Stee... read on
The Vista Stainless Steel Wall Starter System joins new walls to existing masonry. Suitable for both internal and external brick or block walls, the connectors can be slotted tog... read on
Ideal for use as a general reinforcement mesh. DML Expanded Metal Lathing is widely used as a backing to help prevent cracks occurring where different materials meet. Availa... read on
Simple angle bracket which is very versatile, used for timber to timber connections. Material Pre-galvanised mild steel. Benefits Available in various width.... read on
The PC extension side plates function as tie straps where splices occur. EPC option should be used where the beam ends at the post. Standard connectors for post to beam connectio... read on
A reinforcing angle designed to transfer loads between 2 ply floor joists/metal web joists. The L70 Reinforcing Angle may be used in pairs to transfer the loads between floo... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The cramps, once... read on
An inexpensive perforated strip which can easily be cut or bent to provide a quick and reliable method of bracing roof trusses / diagonal strutting to floor joists / holding down... read on
A heavy duty general purpose angle plate manufactured from 2.0mm thick galvanised steel to BS EN 10346 +G275. Features: • Heavy Duty • Ideal for retro-fitting Fixings:... read on
Manufactured from 2.5mm thick galvanised steel, powder coated after fabrication for superior dual coated corrosion protection... read on
The standard hanger is designed for building into brickwork or blockwork. Size options: 150x150mm 150x175mm 150x200mm 150x225mm 150x250mm ... read on
Access for Kurfed & Rebated Tiles Material Coated Mild Steel to EN 10130 Packed 100 per box Weight per 100 0.70kg... read on
Application – Used where new walls are being built directly from existing masonry. Suitable for both internal and external brick or block walls, in buildin... read on
A nail plate system for manual use which enables the construction of timber structures on site to strengthen joints for non-structural applications. Automated production ensures ... read on
The HMBTS type 7 timber frame wall tie is designed to connect the masonry outer leaf to a structural timber frame. Available is a range of sizes to suit cavities from 50mm to ... read on
LUP is a light duty joist hanger for supporting timber joists from timber members. Precision formed and engineered for fast installation and maximum loads. Speed prongs are c... read on
The NS prevents nails/screws from piercing water pipes and electrical cables. Material Pre-galvanised mild steel Suitable On Porteur/Porté : bois massif, ... read on
Attaches window boards to masonry wall. Material: Pre-galvanised mild steel. Item code WBT06 (150mm length). For sizing and technical information please see the document downlo... read on
Frame cramp (supplied in stainless or galvanised steel) for restraining masonry to new or existing structures and for building in non-structural elements (frames etc). Technical... read on
Suitable for timber to timber, timber to masonry and timber to steel applications. Manufactured from heavy duty 3mm thick galvanised steel, these 40mm wide brackets and plates pr... read on
The IC Insulation clip provides a quick and simple method of retaining rigidinsulation within a timber frame panel, creating a controlled gap for services.The IC saves time by al... read on
The IC Insulation clip provides a quick and simple method of retaining rigidinsulation within a timber frame panel, creating a controlled gap for services.The IC saves time by al... read on
90 Degree Angle Bracket 2mm Pre-Galv Simpson Strong- Tie light reinforced angle bracket used for assembling of structrural joinery for internal applications. Pre-galvanised.W1 -... read on
Gripple B-Lock Wire Rope Suspension Kits are ideal to hang signs, HVAC, catenary, electrical cables etc, designed with an innovative fast-locking side release mechanism.FEATURES ... read on
Standard Timber to Timber Hangers. A quick and safe method of joist trimming for light, medium and heavy applications such as supporting floor joists, trimming stair wells, and u... read on
A multi purpose connector designed to be bent on site to suit many timber to timber jointing applications. Manufactured from 1.5mm galvanised steel, powder coated after fabricati... read on
For all applications to enhance bolt performance by reducing timber rotation and joint movement. Place between timbers on an M12 bolt prior to tightening.... read on
Support of short span joists, trap hatches and in-fill timbers in roof space. Designed for fast and economical light duty applications. Material – Produced from 0.8... read on
An economical on-site method of butt jointing timbers of similar section. Suitable for use when replacing rotten floor joist ends, replacement of fire damaged timbers and repairi... read on
A pre-galvanised bracket designed to attach window boards to masonry wall. Material – Manufactured from 13 x 3mm galvanised steel to BS EN 10346 + G275. PER BOX OF... read on
Manufactured from galvanised 40x3mm mild steel, powder coated after fabrication for superior dual coated corrosion protection. Size options: 45x45x40mm 90x45x40mm 90x... read on
Partition Mounting Material Galvanised Mild steel to BS EN 10142:2000 Packed 100 per box Weight per 100 0.70kg ... read on
Galvanised mild steel Thickness 0.5mm Packed 500 per box Weight per 100: 2.25Kg ... read on
The ITSE hanger incorporates the ‘‘Strong Grip’’ which secures theI-joist without the need for any fasteners - where no uplift is required. Value-engin... read on
An expanded metal mesh available in various widths, stainless or galvanised steel. Designed to be incorporated into masonry for crack control. Mesh size 20mm x 10mm. Galvanised w... read on
WBFS is a thin profile engineered window board strap used to attach timber window boards to the internal face of a masonry wall and many other non structural general fixing... read on
Universal fixing strap is a reinforced 1mm galvanised strap suitable for many DIY and other non structural general fixing applications. Product Code - UFS Width (mm) - 30 ... read on
Universal, flexible and simple to install, the EWH is an engineered hanger that has been designed to fulfil a wide variety of installation options. Material 275 g/m2 Pre... read on
Scrolled hip irons provide decorative restraint and securely anchor ridge tiles on hipped roofs, preventing water ingress and protecting the roof from potential damage caused by ... read on
This steel frame channel system is designed to tie brickwork to steel studding. Self drill/self-tap screws fix through the channel insulation into the steel studding. The screws ... read on
