Bearings are shielded to prevent penetration of dust and grease packed for life.They should not be cleaned with solvent or lubricated as this will dissolve the grease and cause pre... read on
For coves and part of a rule joint.SpecificationsD=50.8 mmC=1 1/4 inchC=31.7 mmR=1 inchR=25.4 mmOL=70 mmShank Diameter=1/2 inchFor stationary machines at max. recommended speed 18,... read on
A range of small sized panelling cutters. Ideal for veining and fluting applications.SpecificationsD=3/8 inchD=9.5 mmC=7.5 mmR=4.8 mmOL=48 mmShank Diameter=1/4 inchTip width=1.69 ... read on
Trend weather seal recessing tool is designed to accomodate the popular Schlegel Aquamac 63 or Exitex Aquatex P6 weather strip system and allows for a particularly small gap betwee... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1 1... read on
Solid Carbide for long life.Ideal for engraving and veining work.SpecificationsD=5 mmC=15 mmC2=16 mmA=82.5 degreesShank Diameter=1/4 inchOL=64mmGeneral InformationNett Weight (kg):... read on
These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a tem... read on
Two flute straight cutter with 3 degree taper.Designed for constructing wooden vacuum forming moulds.Tapered sides will allow the mould to release easily.SpecificationsD=12.7 mmC=3... read on
Use for producing mortar grooves and for bevelling applications.SpecificationsD=38 mmC=27 mmC2=25.5 mmA=60 degreesOL=62.5 mmShank Diameter=1/2 inchFlat produced=12.5mmGeneral Infor... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=12.7 mmC=5.8 mmC2=9 mmOL=52.7 mmA=45 degreesShank ... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=51 mmC=25 mmC2=35 mmA=45 degreesOL=82 mmShank Diam... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=40 mmC=19 mmC2=26.5 mmA=45 degreesOL=71 mmShank Di... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=32 mmC=15 mmC2=22 mmA=45 degreesOL=66 mmShank Diam... read on
Especially designed bevel cutter for routing Corian and similar luxury 'marble like, material which is used in many bathrooms and kitchens.SpecificationsD=24 mmC=25 mmA=75 degreesO... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=27.5 mmC=13 mmC2=18.38 mmA=45 degreesOL=59 mmShank... read on
To increase gluing area producing a strong joint in drawer production.SpecificationsD=25.4 mmC=12.7 mmOL=49 mmShank Diameter=1/2 inchTimber thickness min.=15 mmTimber thickness max... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=22.28 mmC=6 mmC2=12 mmA=30 degreesOL=54.5 mmShank ... read on
To rout butterfly key and splines in timbers and man-made boards.Use in conjunction with 104 deg (14 deg) dovetail cutter ref. L120 which cuts dovetail pocket.Use in a router table... read on
Template thickness should be at least 5mm thicker than cutter cut length of cutter.Approximately 1.0mm flat will be found on the nose.SpecificationsD=1/2 inchD=12.7 mmC=16 mmB=12.7... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=11 mmC=5.0 mmC2=7.7 mmOL=54.5 mmA=45 degreesShank ... read on
Use for producing mortar grooves and for bevelling applications.SpecificationsD=41 mmC=22.5 mmC2=23 mmA=45 degreesOL=62.5 mmBottom flat diameter = 8.8mmShank Diameter=1/2 inchGener... read on
Machining of this joint is carried out by routing one piece with the inside face on the table.The matching corner inside face is machined upright against the fence.Make sure that t... read on
To make round boxes, planters, barrels or other multi-sided components.One side of the component is machined with the cutter.Fast and accurate joint creation on timber.For use in a... read on
These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a tem... read on
These specially designed machine bits have a specially designed form of scriber to allow use at high speeds. For recessing circular hinges. For accurate repetitive routing, a tem... read on
Ideal for fast chamfering.Popular in the sign making trades.For chamfering edges of plastic material.SpecificationsC=10 mmC2=14 mmP=5.5 mmA=45 degreesOL=53.5 mmShank Diameter=1/4 i... read on
Useful for bevelling thick timbers.Certain sizes can be used for jointing, boxes, pilasters and carcassing.Ideal for use by wood turners with smaller routers to create staves on 25... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.Is ideal for imitating 'V' jointed tongue and groove on man-made b... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=11 mmC=5.0 mmC2=7.7 mmOL=52.5 mmA=45 degreesShank ... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=12.7 mmC=5.8 mmC2=9 mmOL=54 mmA=45 degreesShank Di... read on
To make round boxes, planters, barrels or other multi-sided components.One side of the component is machined with the cutter.Fast and accurate joint creation on timber.For use in a... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=27.5 mmC=13 mmC2=18.38 mmA=45 degreesOL=59 mmShank... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=17.5 mmC=8 mmC2=11.31 mmOL=52.7 mmA=45 degreesShan... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=17.5 mmC=8 mmC2=11.31 mmOL=52.7 mmA=45 degreesShan... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.Is ideal for imitating 'V' jointed tongue and groove on man-made b... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.Is ideal for imitating 'V' jointed tongue and groove on man-made b... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.Is ideal for imitating 'V' jointed tongue and groove on man-made b... read on
Template thickness should be at least 5mm thicker than cutter cut length of cutter.Approximately 1.0mm flat will be found on the nose.SpecificationsD=1/2 inchD=12.7 mmC=12.7 mmB=12... read on
Use for bevelling, chamfering and for producing mortar grooves.Approximately 1.0mm flat will be found on the nose.SpecificationsD=1/2 inchD=12.7 mmC=10.3 mmC2=11.9 mmA=60 degreesOL... read on
Especially designed bevel cutter for routing Corian and similar luxury 'marble like, material which is used in many bathrooms and kitchens.Designed to trim surface to an undermount... read on
For coves and part of a rule joint.SpecificationsD=1/8 inchD=3.2 mmC=9.5 mmR=1/16 inchR=1.6 mmOL=45 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 11Gross Weight (kg... read on
For coves and part of a rule joint.SpecificationsD=4.8 mmC=7/16 inchC=11 mmR=3/32 inchR=2.4 mmOL=60 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 12Gross Weight (kg... read on
For coves and part of a rule joint.SpecificationsD=6.4 mmC=7/16 inchC=11.0 mmR=1/8 inchR=3.2 mmOL=60.5 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 14Gross Weight ... read on
For coves and part of a rule joint.SpecificationsD=6 mmC=15 mmR=3 mmOL=58.5 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 11Gross Weight (kg): 33Barcode SKU: 502765... read on
For coves and part of a rule joint.SpecificationsD=8 mmC=1/2 inchC=12.7 mmR=4 mmOL=56.7 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 11Gross Weight (kg): 27Barcode... read on
For coves and part of a rule joint.SpecificationsD=10 mmC=18 mmR=5 mmOL=58 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 13Gross Weight (kg): 29Barcode SKU: 5027654... read on
For coves and part of a rule joint.SpecificationsD=12.7 mmC=19 mmR=1/4 inchR=6.3 mmOL=56 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 25Gross Weight (kg): 64Barcod... read on
For coves and part of a rule joint.SpecificationsD=1/2 inchD=12.7 mmC=19 mmOL=59 mmR=1/4 inchR=6.3 mmOL=47 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 19Gross Wei... read on
For coves and part of a rule joint.SpecificationsD=14 mmC=18 mmR=7 mmOL=60 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 51Gross Weight (kg): 72Barcode SKU: 5027654... read on
For coves and part of a rule joint.SpecificationsD=16 mmC=19.5 mmR=5/16 inchR=8 mmOL=57.5 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 52Gross Weight (kg): 73Barco... read on
For coves and part of a rule joint.SpecificationsD=16 mmC=19.5 mmR=5/16 inchR=8 mmOL=51 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 21Gross Weight (kg): 43Barcode... read on
For coves and part of a rule joint.SpecificationsD=19.1 mmC=31.7 mmR=3/8 inchR=9.5 mmOL=71 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 82Gross Weight (kg): 114Bar... read on
For coves and part of a rule joint.SpecificationsD=18 mmC=19 mmR=9 mmOL=57 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 56Gross Weight (kg): 81Barcode SKU: 5027654... read on
For coves and part of a rule joint.SpecificationsD=18 mmC=19 mmR=9 mmOL=48 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 27Gross Weight (kg): 30Barcode SKU: 5027654... read on
For coves and part of a rule joint.SpecificationsD=1 inchD=25.4 mmC=5/8 inchC=15.9 mmR=1/2 inchR=12.7 mmOL=56 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 77Gross ... read on
For coves and part of a rule joint.SpecificationsD1=20 mmCut length=18 mmOL=57 mmR1=10 mmShank Diameter=1/2 inchesGeneral InformationNett Weight (kg): 43Gross Weight (kg): 86Barcod... read on
For coves and part of a rule joint.SpecificationsD=20 mmC=18 mmR=10 mmOL=46 mmShank Diameter=1/4 inchGeneral InformationNett Weight (kg): 33Gross Weight (kg): 53Barcode SKU: 502765... read on
Template thickness should be 5mm thicker than cut length of cutter.SpecificationsD=1/2 inchD=12.7 mmC=9.5 mmB=12.7 mmR=1/4 inchR=6.35 mmOL=50mmShank Diameter=1/4 inchGeneral Inform... read on
Template thickness should be 5mm thicker than cut length of cutter.SpecificationsD=19 mmC=11 mmOL=55 mmB=19 mmR=3/8 inchR=9.5 mmShank Diameter=1/4 inchGeneral InformationNett Weigh... read on
Template thickness should be 5mm thicker than cut length of cutter.SpecificationsD=19 mmC=32 mmOL=80 mmB=19 mmR=3/8 inchR=9.5 mmShank Diameter=1/2 inchGeneral InformationNett Weigh... read on
For coves and part of a rule joint.SpecificationsD=32 mmC=1 1/4 inchC=31.7 mmR=5/8 inchR=16 mmOL=71 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 165Gross Weight (k... read on
Tungsten Carbide Tipped.Two flute cutter with tips sheared up and down, giving a fine finish.For trimming veneered and double-faced boards, plywoods and natural timbers.These cutte... read on
For coves and part of a rule joint.SpecificationsD=1 1/2 inchD=38.1 mmC=1 1/4 inchC=31.7 mmR=3/4 inchR=19.1 mmOL=70 mmShank Diameter=1/2 inchGeneral InformationNett Weight (kg): 20... read on
A range of small sized panelling cutters. Ideal for veining and fluting applications.SpecificationsD=13 mmC=12.5 mmR=6 mmOL=52.5 mmShank Diameter=1/4 inchGeneral InformationNett W... read on
A range of small sized panelling cutters. Ideal for veining and fluting applications.SpecificationsD=14.5 mmC=19.5 mmR=7.5 mmOL=53.5 mmShank Diameter=1/4 inchGeneral InformationNe... read on
Machining of traditional panels and frame doors, formerly done on spindle moulders, can now be performed with heavy duty routers mounted in fixed positions, either overhead or inve... read on
This Raised Panel cutter runs best at lower speeds between 12,000 and 18,000 RPM.Matches our range of profile scribers.Suitable for use on natural timber and MDF.When joining secti... read on
Machining of traditional panels and frame doors, formerly done on spindle moulders, can now be performed with heavy duty routers mounted in fixed positions, either overhead or inve... read on
Machining of traditional panels and frame doors, formerly done on spindle moulders, can now be performed with heavy duty routers mounted in fixed positions, either overhead or inve... read on
Ideal for following templates when panelling and profiling in furniture manufacture.It is advisable that the template is at least 5mm thicker than the cut length of the cutter.Spec... read on
Shank mounted bearing follows template mounted on board surface.It is advisable that the template is at least 5mm thicker than the cutter.SpecificationsD=22 mmC=1/2 inchC=12.7 mmB=... read on
Machining of traditional panels and frame doors, formerly done on spindle moulders, can now be performed with heavy duty routers mounted in fixed positions, either overhead or inve... read on
Machining of traditional panels and frame doors, formerly done on spindle moulders, can now be performed with heavy duty routers mounted in fixed positions, either overhead or inve... read on
Machining of traditional panels and frame doors, formerly done on spindle moulders, can now be performed with heavy duty routers mounted in fixed positions, either overhead or inve... read on
Shape similar to Ref. 18/80.Suitable panel mould for use with Ref. PSC/5 & PSC/50.SpecificationsD=28.5 mmC=38 mmA=75 degreesOL=76 mmShank Diameter=1/2 inchChamfer height= 27.5 mmSh... read on
To create profiles in the face or edge of drawer fronts and cabinet doors.SpecificationsD=19 mmD2=6.5 mmC=11 mmR=4 mmOL=53 mmShank Diameter=1/4 inchGeneral InformationNett Weight (... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Cutters of 2.0mm di... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Cutters of 2.0mm di... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Cutters of 2.0mm di... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Cutters of 2.0mm di... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Small diameter tool... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Small diameter tool... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Cutters with prefix S are Solid Carbide.Cutters of 2.0mm di... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Small diameter tools must be handled with care to avoid bre... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Small diameter tools must be handled with care to avoid bre... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Small diameter tools must be handled with care to avoid bre... read on
Eccentric single flute cutters.Cutters are chosen for fast free cutting, when cutting speed takes preference over finish.Small diameter tools must be handled with care to avoid bre... read on
Template thickness should be 5mm thicker than cut length of cutter.Can be used to rout both tenons and housings.SpecificationsD=3/4 inchD=19.1 mmC=11.1 mmB=19.1 mmOL=63.5 mmShank D... read on
Template thickness should be 5mm thicker than cut length of cutter.Can be used to rout both tenons and housings.SpecificationsD=3/4 inchD=19.1 mmC=11.1 mmB=19.1 mmOL=57 mmShank Dia... read on
Template thickness should be 5mm thicker than cut length of cutter.Can be used to rout both tenons and housings.SpecificationsD=1 inchD=25.4 mmC=11.1 mmB=25.4 mmOL=64 mmShank Diame... read on
Template thickness should be 5mm thicker than cut length of cutter.Can be used to rout both tenons and housings.SpecificationsD=1 1/2 inchD=38.1 mmC=16 mmB=38.1 mmOL=69 mmShank Dia... read on
Produces an elegant edge mould, or a shallow panel effect when routing on its full width.SpecificationsD=20 mmC=15 mmR=6 mmOL=53 mmShank Diameter=1/2 inchGeneral InformationNett We... read on
Flat Roman Ogee, for raised panelling or edge moulding. Used for decorative capping on hand rails.SpecificationsD=41.5 mmC=8 mmC2=8 mmR=19 mmR2=11 mmOL=56 mmShank Diameter=1/2 inch... read on
Flat Roman Ogee, for raised panelling or edge moulding. Used for decorative capping on hand rails.SpecificationsD=50 mmC=6.5 mmC2=11.5 mmR=20 mmR2=12 mmOL=51.8 mmShank Diameter=1/2... read on
These plug cutters produces plugs to exactly fit counterbored holes produced by Ref. 62 & 63 group tools.Use at recommended speeds of 1000-20000 RPM.SpecificationsD=12 mmC=16 mmOL=... read on
These plug cutters produces plugs to exactly fit counterbored holes produced by Ref. 62 & 63 group tools.Use at recommended speeds of 1000-20000 RPM.SpecificationsD=16 mmC=16 mmOL=... read on
These plug cutters produces plugs to exactly fit counterbored holes produced by Ref. 62 & 63 group tools.Use at recommended speeds of 1000-20000 RPM.SpecificationsD=3/8 inchD=9.5 m... read on
To adjust the groove width these tools can be re-assembled with the supplied shims and spacers inserted between the groovers, giving a 0.1mm increment in thickness.SpecificationsD... read on
To adjust the groove width these tools can be re-assembled with the supplied shims and spacers inserted between the groovers, giving a 0.1mm increment in thickness.SpecificationsD... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/32 inchD=4 mmC=11 mmOL=63 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/32 inchD=4 mmC=11 mmOL=65 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/4 inchD=6.3 mmC=19 mmOL=64 mm... read on
To produce an undercut on relief lettering to create a more aesthetic appearance, as well as for edge grooving.SpecificationsD=3/4 inchD=19.1 mmC=1/8 inchC=3.2 mmB=12.7 mmE=3.2 mmO... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=4.5 mmC=11 mmOL=51 mmShank Diam... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=2.5 mmC=8 mmOL=48 mmShank Diame... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=3 mmC=11 mmOL=59 mmShank Diamet... read on
To produce an undercut on relief lettering to create a more aesthetic appearance, as well as for edge grooving.SpecificationsD=1 inchD=25.4 mmC=1/4 inchC=6.3 mmB=12.7 mmOL=55 mmE=6... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/64 inchD=2 mmC=5 mmOL=50 mmSh... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/32 inchD=4 mmC=15.9 mmOL=56 m... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1/2... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1/2... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=3/16 inchD=4.7 mmC=11 mmOL=56 m... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=3/16 inchD=4.7 mmC=11 mmOL=51 m... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/8 inchD=3.2 mmC=11 mmOL=56 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/8 inchD=3.2 mmC=11 mmOL=59 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=3.4 mmC=11 mmOL=51 mmShank Diam... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/4 inchD=6.3 mmC=11 mmOL=44 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=7/32 inchD=5.5 mmC=19 mmOL=51 m... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=13/64 inchD=5 mmC=16 mmOL=64.5 ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=13/64 inchD=5 mmC=16 mmOL=69 mm... read on
A two flute cutters with extra long shanks.Deep grooving, rebating and mortising.Useful for template work when thickness of template restricts depth.Extra care must be taken to avo... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/4 inchD=6.3 mmC=16 mmOL=69 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/4 inchD=6.3 mmC=16 mmOL=59 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/4 inchD=6.3 mmC=25 mmOL=70 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=1/4 inchD=6.3 mmC=25 mmOL=69 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=6.5 mmC=25 mmOL=57 mmShank Diam... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD1=6 mmCut length=25 mmOL=65 mmSh... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD1=6 mmCut length=25 mmOL=57 mmSh... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=15/64 inchD=6 mmC=16 mmOL=69 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=15/64 inchD=6 mmC=16 mmOL=59 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=19/64 inchD=7.5 mmC=19 mmOL=51 ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=9/32 inchD=7 mmC=19 mmOL=63 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=9/32 inchD=7 mmC=19 mmOL=50 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/16 inchD=8 mmC=25 mmOL=69 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/16 inchD=8 mmC=25 mmOL=57 mmS... read on
For biscuit jointing of timber, man-made fibre and particle board with the router.The set includes three sizes of bearing which set the correct depth of cut for the three sizes av... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/16 inchD=8 mmC=25 mmOL=70 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/16 inchD=8 mmC=25 mmOL=70 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=8.1 mmC=25 mmOL=70 mmShank Diam... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=8.9 mmC=25 mmOL=70 mmShank Diam... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/16 inchD=8 mmC=19 mmOL=65 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=5/16 inchD=8 mmC=19 mmOL=52 mmS... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=3/8... read on
A keyhole recess for picture hanging flush to the wall.Ref. 35/0 - No.8 & No.10 screw heads.Not suitable for grooving applications.SpecificationsD=9.5 mmD2=4.5 mmS=5.5 mmC=4.5 mmOL... read on
A range of heavy duty 'T' slot cutters for clamping and hanging applications.MEC mechanical feed only.SpecificationsD=28 mmD2=11.2 mmC=4 mmR=2 mmOL=52 mmShank Diameter=3/8 inchGene... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=3/8... read on
Slots for concealing electric cables etc.A 6mm slot must be cut first to allow for the cutter neck.Care must be taken to avoid breakage.SpecificationsD=12 mmD2=4 mmS=10.0 mmOL=53 m... read on
Ideal for hiding pipes and cables.Part of curve can be used for producing decorative edges.An initial slot is required before using the ball groovers.SpecificationsD=12.7 mmD2=6.5 ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=9 mmC=25 mmOL=70.5 mmShank Diam... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=23/64 inchD=9 mmC=19 mmOL=68 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.SpecificationsD=23/64 inchD=9 mmC=19 mmOL=51 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.TC tips are ground ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.Short shank for Mak... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.Short shank for Mak... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=31/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=7/1... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=7/1... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1/2... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.TC tips are ground ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1/2... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1/2... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1/2... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.Ideal for cutting k... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.Ideal for cutting k... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Short shank for Makita 3600B & 3612BR, Ryobi an... read on
TCT extra long cutter.Two flutes give a clean finish to cut edges.Use only on professional routers with 80mm deep plunge and suitable one piece multi-slit collet to ensure safe cut... read on
A two flute cutters with extra long shanks.Deep grooving, rebating and mortising.Useful for template work when thickness of template restricts depth.Extra care must be taken to avo... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Ideal for cutting kitchen worktops.Specificatio... read on
Extra long two flute cutter for routing hollow honey-comb work top boards only.Use only in professional routers with an 80mm deep plunge and suitable one piece multi-slit collet to... read on
Two flute TC cutter giving good chip clearance.Ideal for shallow lateral routing cuts such as recessing hinges.Corners will require final trimming square with a hand chisel or a co... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=33/... read on
For dovetail joints and sliding dovetails.Can be used with Ref.10/40 butterfly 14 degree spline cutter.SpecificationsD1=12.7 mmC=10 mmOL=60 mmA=104 degreesShank Diameter=1/2Genera... read on
For dovetail joints and sliding dovetails.Can be used with Ref.10/40 butterfly 14 degree spline cutter.SpecificationsD1=25.4 mmC=25.4 mmA=104 degreesOL=69 mmShank Diameter=1/2Gene... read on
For dovetail joints and sliding dovetails.Can be used with Ref.10/40 butterfly 14 degree spline cutter.SpecificationsD1=19.1 mmC=19.1 mmOL=66 mmA=104 degreesShank Diameter=1/2Gene... read on
Purpose made for stair housing jigs.Ensures tight fit of tread in string.SpecificationsD=14 mmC=20 mmOL=65 mmA=95 degreesShank Diameter=1/2 inchGeneral InformationNett Weight (kg):... read on
Purpose made for stair housing jigs.Ensures tight fit of tread in string.SpecificationsD=5/8 inchD=16 mmC=26 mmOL=65 mmA=95 degreesShank Diameter=1/2 inchGeneral InformationNett We... read on
Purpose made for stair housing jigs.Ensures tight fit of tread in string.SpecificationsD1=3/4 inchD1=19 mmC=25.5 mmOL=65 mmA=95 degreesShank Diameter=1/2 inchGeneral InformationNet... read on
Purpose made for stair housing jigs.Ensures tight fit of tread in string.SpecificationsD=7/8 inchD=22 mmC=26 mmA=95 degreesOL=63.5 mmShank Diameter=1/2 inchRotation=Left handGener... read on
Purpose made for stair housing jigs.Ensures tight fit of tread in string.SpecificationsD=7/8 inchD=22 mmC=26 mmOL=65 mmA=95 degreesShank Diameter=1/2 inchGeneral InformationNett We... read on
Heavy duty arbor with spacers for 12mm bore slotters with or without bearings.SpecificationsOL=84.5 mmSpigot dia.=12 mmSpigot length incl thread=45 mmSpigot thread length=20 mmDiam... read on
Slotters with M12x1.0 threaded bore enables flush recessing in the corner such as for weather proofing.Spacers are supplied to ensure the minimal threaded arbor protrudes below the... read on
Slotters with M12x1.0 threaded bore enables flush recessing in the corner such as for weather proofing.Spacers are supplied to ensure the minimal threaded arbor protrudes below the... read on
Standard duty arbor with 1/4 inch spindle and spacers.Enables mounting of 1/4 inch bore slotters with and without bearings in a variety of positions.Use shims/spacers to prevent b... read on
Standard duty arbor with 1/4 inch spindle and spacers.Enables mounting of 1/4 inch bore slotters with and without bearings in a variety of positions.Use shims/spacers to prevent b... read on
Standard duty arbor with 1/4 inch spindle and spacers.Enables mounting of 1/4 inch bore slotters with and without bearings in a variety of positions.Use shims/spacers to prevent b... read on
Recessing cutter will accommodate the Schlegel Aquamac 21 or Exitex Aquatex A10 seal.The cutter is designed for use with the seal in a wiping mode and comes complete with a guide b... read on
A one piece bearing guided set.Parts are inter-changed on the arbor to alter the set-up.SpecificationsD=41 mmC=6.35 mmC2=10 mmE=22 mmOL=76 mmShank Diameter=1/2 inchTimber thickness... read on
A complete cutter set for producing matchlining.Jointing parts are interchanged on the arbor to change the mode of the cutter.SpecificationsD=47 mmC=11 mmC2=6 mmB=34 mmB2=22 mmOL=7... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=2 mmNo. of Teeth=4Genera... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=3 mmNo. of Teeth=4Genera... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=5 mmNo. of Teeth=4Genera... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=4 mmNo. of Teeth=4Genera... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=6 mmNo. of Teeth=4Genera... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=8 mmNo. of Teeth=4Genera... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=11 mmNo. of Teeth=4Gener... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=40 mmBore=M12Kerf=10 mmNo. of Teeth=2Gener... read on
These slotters have a 12mm clear bore to enable them to be mounted at any position on the arbor in combination with spacers, with or without a bearing.SpecificationsD=50 mmBore=12 ... read on
All slotters are precision made in TCT grade for long life when cutting the most abrasive materials.SpecificationsD=41.3 mmKerf=6.0 mmNo. of Teeth=2General InformationNett Weight (... read on
These slotters have a 12mm clear bore to enable them to be mounted at any position on the arbor in combination with spacers, with or without a bearing.SpecificationsD=50 mmBore=12 ... read on
All slotters are precision made in TCT grade for long life when cutting the most abrasive materials.SpecificationsD=41.3 mmKerf=8.0 mmNo. of Teeth=2General InformationNett Weight (... read on
These slotters have a 12mm clear bore to enable them to be mounted at any position on the arbor in combination with spacers, with or without a bearing.SpecificationsD=50 mmBore=12 ... read on
These slotters have a 12mm clear bore to enable them to be mounted at any position on the arbor in combination with spacers, with or without a bearing.SpecificationsD=50 mmBore=12 ... read on
All slotters are precision made in TCT grade for long life when cutting the most abrasive materials.SpecificationsD=41.3 mmKerf=10 mmNo. of Teeth=2General InformationNett Weight (k... read on
Bearing guided tool to rout multi-point lock systems in wooden doors.Two flute for clean finish.Use in conjunction with multi-point lock system cutter ref. 4/09X1/2TC.Specification... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=9.5 mmNo. of Teeth=4Gene... read on
Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door.Two sizes available to suit 4mm thick strip of 10mm or 15mm width.Intumescen... read on
Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door.Two sizes available to suit 4mm thick strip of 10mm or 15mm width.Intumescen... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=7 mmNo. of Teeth=4Genera... read on
All slotters are precision made in TCT grade for long life when cutting the most abrasive materials.SpecificationsD=40 mmKerf=7.0 mmNo. of Teeth=4General InformationNett Weight (kg... read on
These slotters have a M12 threaded boss to enable them to be threaded onto the arbor without the need for a securing nut.SpecificationsD=50 mmBore=M12Kerf=2.5 mmNo. of Teeth=4Gene... read on
For biscuit jointing of timber, man-made fibre and particle board with the router.The set includes three sizes of bearing which set the correct depth of cut for the three sizes av... read on
For biscuit jointing of timber, man-made fibre and particle board with the router.The set includes three sizes of bearing which set the correct depth of cut for the three sizes av... read on
Recessing cutter is designed to accommodate the Carripile I style weatherstrip.It comes complete with a guide bearing to reduce setting-up time and is particulary useful for the me... read on
Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door.A range of sizes available to suit 4mm thick strip from 10mm to 25mm width.I... read on
Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door.A range of sizes available to suit 4mm thick strip from 10mm to 25mm width.I... read on
A keyhole recess for picture hanging flush to the wall.Ref. 35/01 - No.10 & No.12 screw heads.Not suitable for grooving applications.SpecificationsD=12.7 mmD2=8 mmS=4.6 mmC=4.9 mmO... read on
A range of heavy duty 'T' slot cutters for clamping and hanging applications.Relief cut required.SpecificationsD=28 mmD2=9.5 mmC=8 mmOL=60 mmShank Diameter=3/8 inchGeneral Informat... read on
A range of heavy duty 'T' slot cutters for clamping and hanging applications.Relief cut required.SpecificationsD=35 mmD2=12.7 mmC=9.5 mmOL=65 mmShank Diameter=1/2 inchGeneral Infor... read on
A range of heavy duty 'T' slot cutters for clamping and hanging applications.Relief cut required.MEC mechanical feed only.SpecificationsD=30 mmD2=10.5 mmC=7 mmR=3 mmA=119 degreesOL... read on
Bearing guided intumescent strip cutter for routing the groove for intumescent strip in a frame or door.A range of sizes available to suit 4mm thick strip from 10mm to 25mm width.I... read on
Recessing cutter for producing double rebates.For producing recesses with a lower rebate.Designed to accept library/bookcase strip.SpecificationsD=13 mmD2=19 mmC= 10 mmC2= 6 mmOL=... read on
Recessing cutter for producing double rebates.For producing recesses with a lower rebate.Designed to accept library/bookcase strip. Specifically designed for Tonk Strip.Specifica... read on
Recessing cutter for producing double rebates.For producing recesses with a lower rebate.Designed to accept library/bookcase strip. Specifically designed for Tonk Strip.Specifica... read on
Four fluted cutter for routing tenons with a clean finish on the shoulder.Tungsten Carbide Tipped for use on timber and abrasive man-made boards.Cutter has four cutting edges with ... read on
Has three flutes, and has bevelled corners to prevent scoring, and is for flush trimming of hardwood or plastic edge strip.SpecificationsD=25 mmC=12 mmA=90 degreesOL=44.5 mmShank D... read on
These slotters have a 12mm clear bore to enable them to be mounted at any position on the arbor in combination with spacers, with or without a bearing.Requires heavy duty arbor acc... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=35/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=35/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=35/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=15 ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=9/1... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=7/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1 i... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1 i... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD1=15... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=33/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=33/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1 3... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=1 1... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=2 i... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=19/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=19/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=43/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=43/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD1=16... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD1=16... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=45/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=45/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=5/8... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=45/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=23/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=23/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=23/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=3/4... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=3/4... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=19.... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=3/4... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=3/4... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=55/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=55/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=53/... read on
Self-guiding trimmers with bearings mounted on end of cutter.For trimming plastic or plywood overlay.For copy profiling, use the bearing to follow a template or base edge of board.... read on
Cut a wider edge line, at an angle of 80 degrees.A 16mm bearing is supplied as standard.A larger 19mm bearing will spread the wear of the cutting edges.SpecificationsD=20 mmC=14 mm... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=22 ... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=25/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=63/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=63/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=29/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=29/... read on
TCT for abrasive materials such as chipboard, MDF, plywood, hardwoods and hard plastics.Two flutes give a clean finish to cut edges.Has a TCT plunge centre tip.SpecificationsD=61/... read on
