Account
We offer FREE UK Mainland delivery for orders over £50! (EX VAT exclusions apply).
We offer FREE UK Mainland delivery for orders over £50! (EX VAT exclusions apply).
Found 60 product(s). Showing product(s) 1 to 60.
These products act to secure two leaves of a cavity wall to each other, allowing them to act as one structurally. A cavity tie usually incorporates some mechanism, (usually a cha... read on
A 4.5mm Newbuild wall tie for securing external masonry to timber frames. The first helical wall tie was tested to EN846 for timber frame construction. Used for domestic and smal... read on
SIZES 200mm 225mm 250mm 275mm BBA Approved light duty housing ties (Agrément Certificate: 17/5462). Application - A light duty wall tie u... read on
Resin to Resin Remedial Wall Ties (HELI-4.5-ONE, HELI-6-ONE) Used when the existing ties have either corroded or insufficient ties have been used. Tying both the inner (load bea... read on
When fixing a stainless steel tie to a mild steel frame, an isolation pad should be used to separate the dissimilar metals and prevent a bimetallic reaction.... read on
SST Starter Tie supplied complete with nylon plug. Used where new walls are being built directly from existing brickwork. Alternatively can be used without plug and screwed direc... read on
Supplied complete with 50mm x 3.35mm Stainless Steel Annular Ring Nails. Application - This type of timber frame wall tie is right for domestic and small commerci... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
BBA Approved general purpose wall ties (Agrément Certificate: 17/5462). Application - A general-purpose wall tie for applications such as small commercial bui... read on
The VST1 tie range has a Multidrip feature to prevent moisture from traveling across the cavity. Its categorisation as a Type 1 wall tie means the VST1 tie is suitable for most b... read on
These products both allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These sy... read on
Soffit fixed both sides where fixings can be made directly above. Heavy Duty. Hole size standard 12mm to suit M10 expansion bolts or M10 head bolt. Design load resistant dependan... read on
Used to stabilise solid or rubble walls, repair delaminated brickwork and to reconnect separated internal party walls to the external leafs. Installation: 1. Drill hole to requ... read on
These products allow new walls to be joined to existing structures. They can be used to extend an existing structure, or they can be used to help create an additional leaf where ... read on
A range of heavy duty (welded) and light duty (bent and/or twisted) stems. Available in standard stem lengths, head sizes and hole configurations with other options available on ... read on
This range of ties allow masonry walls to be tied back to other structures (steelwork or masonry) providing restraint in one direction but allowing movement in the other. This is... read on
A heavy-duty wall tie suitable for most buildings in the UK of any height, with cavities up to 150mm. Used for collar jointed walls, in full fill cavities or where the prevention... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
SST Starter Tie supplied complete with nylon plug. Used where there is a cavity and a new wall needs to be built. Supplied with drip. SST-225-STST Compressive... read on
A range of heavy duty (welded) and light duty (bent and/or twisted) stems. Available in standard stem lengths, head sizes and hole configurations with other options available on ... read on
SSFT Starter Frame Tie. Used for fixing timber door and window frames to brickwork by building into mortar courses as construction progresses Compressive Load Capacity: ... read on
These products both allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These sy... read on
This range of ties allows masonry walls to be tied back to other structures, (steelwork or masonry) providing restraint in one direction but allowing movement in the other. This ... read on
These products allow the introduction of a cavity tie into a sitation where no ties are present. These stainless steel ‘wavy’ tail ties are used for remedial applicat... read on
This range of ties allows masonry walls to be tied back to other structures, (steelwork or masonry) providing restraint in one direction but allowing movement in the other. This ... read on
BBA Approved general purpose wall ties (Agrément Certificate: 17/5462). Application – A general-purpose wall tie for applications such as small commerci... read on
These products allow masonry walls to be restrained back to other elements of the structure. The ties, once in position, prevent sideways movement between a wall and another stru... read on
These products allow vertical movement whilst offering horizontal restraint. The channel system tends to be face-fixed while the slot is usually cast into concrete. These systems... read on
Soffit Fixed both sides where fixings can be made directly above. Heavy duty. Hole size standard 12mm to suit M10 expansion bolts or M10 head bolt. Design load resistant dependan... read on
Stainless steel masonry-timber tie for domestic and small commercial buildings up to four storeys high. Suitable for buildings with a maximum height if 15m and cavity widths from... read on
Drip feature to prevent moisture travelling across the cavity (taking less space than vertical twist). Drip position 90mm from safety end as standard. 250mm long stainless steel ... read on
Used as a soffit fixed head restraint. Light Duty, twisted head allows for fixing a right angle for cavity. Hole size standard 12mm to suit M10 expansion bolts or M10 head bolt. ... read on
It's common practice to cut a hole in the tops of the floor joists so that pipes and electrical cables can pass through the void between an upper floor and ceiling below it - par... read on
Vertical Twist feature to prevent moisture travelling across the cavity. The design means that the tie can be installed either way up. It’s categorisation as a Type 1 wall ... read on
The Vista TPT is designed to safely tie across large cavities in traditional brick/blocks. As a result of problems experienced over wider cavities (150- 375mm) and their weight c... read on
Vista have developed Vista Weld 3 to meet the ever increasing requirements of specifiers. Vista Weld 3 is a welded ladder type Bed Joint Reinforcement with 3mm outer wires. It is... read on
FB20 fixing band is for all general light strapping needs. Perfect for DIY, industrial and agricultural applications. Comes in convenient 10 metre rolls. FB20, which comes suppl... read on
The VHR head restraint is designed to restrain the top of the inner leaf of cavity walls. The standard restraint consists of 2 angles and can be used to restrain both 100mm and 1... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
The Vista Stainless Steel Wall Starter System joins new walls to existing masonry. Suitable for both internal and external brick or block walls, the connectors can be slotted tog... read on
An inexpensive perforated strip which can easily be cut or bent to provide a quick and reliable method of bracing roof trusses / diagonal strutting to floor joists / holding down... read on
These products act to secure two leaves of a cavity wall to each other, allowing them to act as one structurally. They incorporates a multidrip feature to discourage moisture mov... read on
Application – Used where new walls are being built directly from existing masonry. Suitable for both internal and external brick or block walls, in buildin... read on
Frame cramp (supplied in stainless or galvanised steel) for restraining masonry to new or existing structures and for building in non-structural elements (frames etc). Technical... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The cramps, once... read on
A pre-galvanised bracket designed to attach window boards to masonry wall. Material – Manufactured from 13 x 3mm galvanised steel to BS EN 10346 + G275. PER BOX OF... read on
An expanded metal mesh available in various widths, stainless or galvanised steel. Designed to be incorporated into masonry for crack control. Mesh size 20mm x 10mm. Galvanised w... read on
The basalt fibre composite Neutras wall tie is an extremely versatile product and has been designed to serve as a uniquely adaptable substitute for traditional steel ties. Neutra... read on
Light duty restraint straps can be used for vertical restraint applications, such as holding down wall plates to masonry. These multi-holed straps are supplied in 100mm increment... read on
These products allow masonry walls to be restrained back to other elements of the structure. This could be pre-existing walls, or new or pre-existing steel work. The ties, once i... read on
For all applications to enhance bolt performance by reducing timber rotation and joint movement. Place between timbers on an M12 bolt prior to tightening. 50xM12 PER BOX OF 100... read on
SST Starter Tie supplied complete with nylon plug. Used where new walls are being built directly from existing brickwork. Alternatively can be used without plug and screwed direc... read on
BBA Approved cavity wall ties (Agrément Certificate: 17/5462). Application – A low thermal conductivity, general-purpose wall tie for applications such ... read on
The basalt fibre composite Neutras wall tie is an extremely versatile product and has been designed to serve as a uniquely adaptable substitute for traditional steel ties. Neutra... read on
Application – Type 2 – A general-purpose wall tie for applications such as small commercial buildings and domestic properties. They are suitable for buildings ... read on
This range of ties allow masonry walls to be tied Back to steelwork providing restraint in one direction but allowing movement in the other. This is achieved by placing a debondi... read on
The HJS a superior alternative to timber strutting, Herringbone Struts offer a cost effective method of providing necessary lateral support to floor joists as required by the Bui... read on
Expanded metal brickwork reinforcement is embedded in mortar joints (usually every third course) to give extra tensile strength to wall and help withstand vibration and sudden lo... read on
Application – Used for fixing timber door and window frames to brickwork by building into mortar courses as construction progresses. Suitable for bui... read on
